Forum: MechMates already cutting
Fri 12 November 2010, 14:48
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Tue 09 November 2010, 07:39
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Wed 20 October 2010, 07:47
|
Replies: 551
Views: 499,126
Thank Nils,
Haven't done allot of plastics,...
Thank Nils,
Haven't done allot of plastics, but I'm sure the time will come.
I'm finally getting my cut quality on hard woods down. Allot less sanding and minimal machine marks.
Funny...
|
Forum: MechMates already cutting
Tue 19 October 2010, 06:29
|
Replies: 551
Views: 499,126
Nils,
Looking back, your rough cut was done...
Nils,
Looking back, your rough cut was done with a 1/2" Bit at 150 IPM.
If you don't mind, would you share your finishing pass information. Also, whats the allowance (how much did you "skim"...
|
Forum: MechMates already cutting
Fri 03 September 2010, 12:21
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Fri 03 September 2010, 10:29
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Fri 03 September 2010, 08:43
|
Replies: 551
Views: 499,126
Thanks Sean. Hope all is good with you too.
...
Thanks Sean. Hope all is good with you too.
Speaking of snakes. Just had to take a dog to the vet last week due to a rattler. Saved my wife though. If it wasn't for "Rocky", my wife would have...
|
Forum: MechMates already cutting
Fri 03 September 2010, 08:28
|
Replies: 551
Views: 499,126
Watch it bud. :) Never said I was fast.
...
Watch it bud. :) Never said I was fast.
Yea, good to be back. Finally resigned from the day job last April and starting a small business. Having a blast. Not profitable yet, but I've got a...
|
Forum: MechMates already cutting
Fri 03 September 2010, 07:52
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Wed 01 September 2010, 13:38
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Sat 31 July 2010, 12:20
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Sat 31 July 2010, 08:27
|
Replies: 551
Views: 499,126
Thanks men,
I think Gerald may have it. ...
Thanks men,
I think Gerald may have it. The lines are 360 degrees around the part. So if the cutter was not "plum" (true vertical), the lines would not be on all the surfaces (360 degrees). ...
|
Forum: MechMates already cutting
Fri 30 July 2010, 18:47
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Fri 30 July 2010, 14:03
|
Replies: 551
Views: 499,126
Agreed.
I think I'll read thru your build...
Agreed.
I think I'll read thru your build again and refresh myself on your setup. I'm still happy with my configuration, but I do allot of sanding on the edges due to the line from each pass...
|
Forum: MechMates already cutting
Fri 30 July 2010, 10:42
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Wed 01 July 2009, 22:10
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Fri 17 April 2009, 05:26
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Fri 02 January 2009, 07:30
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Sun 21 December 2008, 06:34
|
Replies: 551
Views: 499,126
Nils,
Can you make a short video and post...
Nils,
Can you make a short video and post on youtube?
A picture is worth ..... blah, blah, blah,
But, a video with sound may solve your problems faster.
Most digital cameras have video. ...
|
Forum: MechMates already cutting
Sat 20 December 2008, 17:00
|
Replies: 551
Views: 499,126
Nils,
Heath and Doug have good points.
...
Nils,
Heath and Doug have good points.
I have all my motors on the 3rd hole for the springs. It did make a difference.
5 in/sec/sec was a hugh difference in my case. I don't think the...
|
Forum: MechMates already cutting
Fri 19 December 2008, 17:30
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Tue 16 December 2008, 19:12
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Fri 07 November 2008, 17:46
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Wed 29 October 2008, 17:44
|
Replies: 551
Views: 499,126
|
Forum: MechMates already cutting
Mon 22 September 2008, 19:05
|
Replies: 551
Views: 499,126
|