MechMate CNC Router Forum

Go Back   MechMate CNC Router Forum > Search Forums
Reload this Page Search Results
Register Options Profile Last 1 | 3 | 7 Days Today's Posts

Showing results 1 to 8 of 8
Search took 0.00 seconds. Search: Posts Made By: danilom
Forum: MechMates already cutting Thu 17 November 2016, 13:22
Replies: 174
Views: 166,700
Posted By danilom
I must warn you about noise problems on arduino...

I must warn you about noise problems on arduino running cnc firmware (like grbl)
it can pose a problem running along VFD and other drives and transformers. Also connected via USB which has a number...
Forum: MechMates already cutting Fri 30 September 2016, 06:45
Replies: 174
Views: 166,700
Posted By danilom
All CSMIO are pretty much the same, all the IO...

All CSMIO are pretty much the same, all the IO circuits are same except maybe CPU.

Step/dir is differential on all units

as noted on the CSLabs website:
Forum: MechMates already cutting Mon 26 September 2016, 21:40
Replies: 174
Views: 166,700
Posted By danilom
I installed couple of them and can't see any...

I installed couple of them and can't see any reason for IP-S on a mechmate, IP-M has sufficient number of IO and 125khz output is more than enough
Forum: MechMates already cutting Mon 26 September 2016, 17:16
Replies: 174
Views: 166,700
Posted By danilom
I would stay away from these chinese boards. ...

I would stay away from these chinese boards.

Instead you can go with Linuxcnc and Mesa boards, either pci or pci-e 5i25 and maybe some addon card for io or 7i76E ethernet card with lots of IO and...
Forum: MechMates already cutting Thu 25 April 2013, 00:10
Replies: 174
Views: 166,700
Posted By danilom
Running a gcode from arduino is easy , ...

Running a gcode from arduino is easy ,
http://dank.bengler.no/-/page/show/5470_grbl?ref=checkpoint

I was thinking of using it on one machine, but the lack of nice computer inteface is too much...
Forum: MechMates already cutting Fri 28 September 2012, 15:09
Replies: 174
Views: 166,700
Posted By danilom
Check capacitors on motherboard, when they go bad...

Check capacitors on motherboard, when they go bad the cap looks swollen, and swap the PSU. If its not that, then it can be either some windows problems or corrupt Mach3 profile, create a new one with...
Forum: MechMates already cutting Fri 28 September 2012, 10:19
Replies: 174
Views: 166,700
Posted By danilom
It looks like error on all axis's XYZ and they...

It looks like error on all axis's XYZ and they are loosing steps. Usually it indicates a computer problem, check CPU usage in task manager, it should not be 100% more like 50% or below.
Sometimes...
Forum: MechMates already cutting Thu 15 September 2011, 13:28
Replies: 174
Views: 166,700
Posted By danilom
2.2kW is ok but 3kw is just right :) also...

2.2kW is ok but 3kw is just right :)

also for the future reference, advice everyone will give you is:

buy the spindle only and find a quality VFD local. sometimes its in same price range
and...
Showing results 1 to 8 of 8

 
Forum Jump

All times are GMT -6. The time now is 01:24.

Contact Us - www.mechmate.com - Archive - Top

Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.