MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Search
Today's Posts
Mark Forums Read
Showing results 1 to 8 of 8
Search took
0.00
seconds.
Search:
Posts Made By:
KenC
Forum:
Construction started, but not cutting yet
Wed 20 May 2015, 01:16
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,137
Posted By
KenC
on the phase, It does, follow the...
on the phase,
It does, follow the manufacturer's specsheet and you should be ok.
if you don't have one, its impossible to tell the correct pole without expensive equipment or trial and error. the...
Forum:
Construction started, but not cutting yet
Sat 09 May 2015, 01:49
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,137
Posted By
KenC
I derive my circuit from similar circuit. ...
I derive my circuit from similar circuit.
http://www.the12volt.com/installbay/uploads/E33_Latching_Relay_2.gif
Forum:
Construction started, but not cutting yet
Fri 08 May 2015, 22:08
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,137
Posted By
KenC
If it is possible, don't use magnetic contactor....
If it is possible, don't use magnetic contactor. I changed to SSR which has zero-crossing ability, i.e. it will only turn on AC is at 0V of the sinewave and only switch off when the cycle is...
Forum:
Construction started, but not cutting yet
Thu 07 May 2015, 23:11
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,137
Posted By
KenC
4000W/230V= 17.4Amp. You sure you want to...
4000W/230V= 17.4Amp.
You sure you want to run higher than 4kW on single phase?
Forum:
Construction started, but not cutting yet
Sat 11 April 2015, 22:49
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,137
Posted By
KenC
the calculated figure is a guide, not something...
the calculated figure is a guide, not something you must follow to the dot...
IMHO, get the calculated figure & use the nearest voltage you have. btw, nobody really want to use lower voltage,...
Forum:
Construction started, but not cutting yet
Wed 08 April 2015, 21:25
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,137
Posted By
KenC
I would not pick this when I have all the choices...
I would not pick this when I have all the choices in the world. but if that is what I have in the junk pile, I would try it out. won't harm a thing IMHO. If it doesn't work out, then I'll use a...
Forum:
Construction started, but not cutting yet
Tue 07 April 2015, 03:24
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,137
Posted By
KenC
50V won't burn the motor... if it doesn't burn...
50V won't burn the motor... if it doesn't burn your driver 1st.
Forum:
Construction started, but not cutting yet
Wed 01 April 2015, 02:46
Replies:
232
WOW These parts are big!! Toledo, OH
Views:
214,137
Posted By
KenC
7:1? no problem, just build it the way you like...
7:1? no problem, just build it the way you like it.
Other places which you can over kill are, triple your steel weight, 25hp spindle, 50hp vane type vacuum pump, i7 16GB Ram, 32"monitor..... :D
Showing results 1 to 8 of 8
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
02:52
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.