Forum: MechMates already cutting
Wed 13 February 2013, 23:07
|
Replies: 268
Views: 158,837
|
Forum: MechMates already cutting
Wed 13 February 2013, 19:40
|
Replies: 268
Views: 158,837
In engineering, there is such thing as...
In engineering, there is such thing as "Tolerance" because, reality says no one can never get 100% accuracy. 99.999999999999.....9999% is possible but never 100%. I would suggest you go through your...
|
Forum: MechMates already cutting
Sun 22 July 2012, 22:52
|
Replies: 268
Views: 158,837
|
Forum: MechMates already cutting
Fri 24 June 2011, 01:00
|
Replies: 268
Views: 158,837
when you
"Mach3 Menu->Config->Select Native...
when you
"Mach3 Menu->Config->Select Native Units(for motor tuning).
Settings(Alt6) lower right corner mm/inches."
Mach3 will advice that is not for setting you G-code unit...
The best thing...
|
Forum: MechMates already cutting
Tue 21 June 2011, 02:44
|
Replies: 268
Views: 158,837
|
Forum: MechMates already cutting
Mon 20 June 2011, 08:05
|
Replies: 268
Views: 158,837
|
Forum: MechMates already cutting
Mon 20 June 2011, 06:38
|
Replies: 268
Views: 158,837
|
Forum: MechMates already cutting
Mon 20 June 2011, 05:38
|
Replies: 268
Views: 158,837
|
Forum: MechMates already cutting
Sun 19 June 2011, 23:13
|
Replies: 268
Views: 158,837
Love your work!
The box is among the...
Love your work!
The box is among the shallowest I've seen so far in this forum.
2 suggestions, you can have the BOB mounted on the box door, either inside or outside of the box (maybe in a...
|
Forum: MechMates already cutting
Sun 08 May 2011, 04:43
|
Replies: 268
Views: 158,837
From where I'm from we build everything with...
From where I'm from we build everything with bricks... but its going to be a messy job dealing with bricks & mortar. I hope to construct a wood frame based sound barrier which should be faster to...
|
Forum: MechMates already cutting
Sun 01 May 2011, 23:17
|
Replies: 268
Views: 158,837
|
Forum: MechMates already cutting
Wed 22 December 2010, 03:32
|
Replies: 268
Views: 158,837
|
Forum: MechMates already cutting
Tue 21 December 2010, 05:23
|
Replies: 268
Views: 158,837
|
Forum: MechMates already cutting
Thu 25 November 2010, 02:26
|
Replies: 268
Views: 158,837
|
Forum: MechMates already cutting
Mon 22 November 2010, 05:15
|
Replies: 268
Views: 158,837
You shoul be ok.
As long as you secure the...
You shoul be ok.
As long as you secure the angle rigidly & no large free play between the guide bearing & the work piece. Any inaccuracy can be dealt with during your shimming process.
Nice...
|
Forum: MechMates already cutting
Thu 18 November 2010, 21:02
|
Replies: 268
Views: 158,837
|
Forum: MechMates already cutting
Mon 15 November 2010, 04:24
|
Replies: 268
Views: 158,837
Ross, your went to a slaugter house???? My...
Ross, your went to a slaugter house???? My friendly neighbourhood machine shop charged me less then a beer for boring, drill & tapping the scrub holes in less then 2 hours... Even after I told him...
|
Forum: MechMates already cutting
Thu 19 August 2010, 08:37
|
Replies: 268
Views: 158,837
|
Forum: MechMates already cutting
Thu 19 August 2010, 07:54
|
Replies: 268
Views: 158,837
|
Forum: MechMates already cutting
Sun 25 July 2010, 07:12
|
Replies: 268
Views: 158,837
|
Forum: MechMates already cutting
Sat 03 July 2010, 05:51
|
Replies: 268
Views: 158,837
|