MechMate CNC Router Forum
>
Search Forums
Search Results
User Name
Remember Me?
Password
Register
Options
Profile
Last
1
|
3
|
7
Days
Search
Today's Posts
Mark Forums Read
Showing results 1 to 8 of 8
Search took
0.00
seconds.
Search:
Posts Made By:
toad
Forum:
General - MM Build
Wed 01 October 2014, 08:55
Replies:
30
Spoil board question
Views:
37,271
Posted By
toad
I have seen some people put pool filters inline,...
I have seen some people put pool filters inline, not sure how that works.
I have not put anything in line, and just cheap filter media over the holes for air.
If I do need to do filtering in the...
Forum:
General - MM Build
Mon 29 September 2014, 15:02
Replies:
30
Spoil board question
Views:
37,271
Posted By
toad
Hi all; I have a couple 1/4 I holes in the pipe...
Hi all;
I have a couple 1/4 I holes in the pipe for air to get to the bearings.
I am surprised on how good it does.
The pipes are 1 1/4. Going into a 4" PVC Plenum with a 2" from the plenum to the...
Forum:
General - MM Build
Sun 28 September 2014, 17:05
Replies:
30
Spoil board question
Views:
37,271
Posted By
toad
Hi all: Ok, finally received the lightweight...
Hi all:
Ok, finally received the lightweight MDF and got it on the table, resurfaced both sides and sealed the edges and gave it a try. With all valves open, am pulling 8 inches of Vacuum at the...
Forum:
General - MM Build
Fri 26 September 2014, 06:11
Replies:
30
Spoil board question
Views:
37,271
Posted By
toad
top and bottom have both been sealed. I...
top and bottom have both been sealed.
I thinned down wood glue and let it soak in and recoated it again to be sure.
Coated all edges also.
I should have the edges sealed on the spoil...
Forum:
General - MM Build
Thu 25 September 2014, 19:09
Replies:
30
Spoil board question
Views:
37,271
Posted By
toad
Here are two photo's the plenum. Picked up the...
Here are two photo's the plenum.
Picked up the lightweight MDF Today, Now I will see what happens, and also install a gauge to see what's going on at the pump.
Toad
Forum:
General - MM Build
Tue 23 September 2014, 10:17
Replies:
30
Spoil board question
Views:
37,271
Posted By
toad
Hi Gerald, The seal is around the perimeter of...
Hi Gerald,
The seal is around the perimeter of each divided section.
When you turn on the Vacuum, it sucks down the spoil board
and only vacuum loss should be through the spoil board. Correct? ...
Forum:
General - MM Build
Mon 22 September 2014, 10:53
Replies:
30
Spoil board question
Views:
37,271
Posted By
toad
Hi all, All is sealed and painted. I found a...
Hi all, All is sealed and painted.
I found a lightweight MDF that is I am told the same as TruPan.
It has to be ordered, but Hardwoods Store in Gibsonville can get it. I will let you know how it...
Forum:
General - MM Build
Mon 22 September 2014, 09:25
Replies:
30
Spoil board question
Views:
37,271
Posted By
toad
Spoil board question
I recently installed a Vacuum to my table. Table is divided into six sections. with rubber ring around each section. Pulls the spoil board down real tight. I have not put a gauge in the suction...
Showing results 1 to 8 of 8
Forum Jump
User Control Panel
Private Messages
Subscriptions
Who's Online
Search Forums
Forums Home
General - MM Build
About this Forum
The Market Place
Personal Build Histories
Introduce yourself and start planning
Construction started, but not cutting yet
MechMates already cutting
Structure & Mechanics
10. Base Table
20. Gantry
30. Y-Car
40. Z-Slide
50. Toolheads
55. Dust Management
Common Assemblies & Parts
Profiled (laser cut) & bent steel plate
Motors & their mountings
Rails & Rollers
Driving Mechanisms: Rack/pinion, gears, screws, belts & chains
Electrical & Electronic
60. Wiring & Cable Management
70. Control Systems
701. Motor Drives
702. Power Supplies
Computing, Software & Programming
80. Computer Hardware & Software
Graphics & CAD
CAM
CNC motion control software
Utility software
After Building the Beast - Operating , Troubleshooting and Maintenance
General - MM Operating
Cutting various materials - bit selection, feeds, speeds
Troubleshooting
Maintenance
The Show Room
Miscellaneous hardware and software
Human Interface Devices (HID's)
Miscellaneous / General / Whatever / Catchall
Golden Resources
Test Area for this forum
Downloads
Dxf Library
Archives
All times are GMT -6. The time now is
23:55
.
Contact Us
-
www.mechmate.com
-
Archive
-
Top
Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.