MechMate CNC Router Forum

MechMate CNC Router Forum (
-   MechMates already cutting (
-   -   Making Cuts #129 - St Denis, Reunion (

YANLM Wed 17 January 2018 08:04

Making Cuts #129 - St Denis, Reunion
3 Attachment(s)
A report of my project with a modification of the skate.

Borko Wed 17 January 2018 12:56

Welcome aboard. It seems to be nice weather out there in this time of year.:)

YANLM Wed 17 January 2018 13:26

The time is beautiful but a cyclone (named BERGUITTA) threatens us at the moment.

MetalHead Thu 18 January 2018 09:50

Welcome aboard!

jhiggins7 Fri 19 January 2018 05:15


I see you've been around about 5 years. Congratulations on your decision to build a MechMate and on your progress so far.

Regarding the skate. Do I see bolt ends at the far left and far right of the photo? When I used a similarly designed skate, the bolts that rode the top of the rail "wore" to the point that my depth of cut was affected. Thus the grinding wheel became more aggressive on subsequent passes. After noticing this, I found that I had to keep adjusting the bolts as they wore.

To remedy this, later designs of the skate placed bearings where you have bolts so the bearings could ride the top of the rail. The bearings don't wear as you make your passes resulting in better control of the depth of cut.

YANLM Fri 19 January 2018 21:07

you are right. the bolts affect the top of the rail but as I finished the rails.

I did not notice or forget that the skateboard was planned for 115mm and not for the 125mm discs.

YANLM Fri 19 January 2018 21:22

5 Attachment(s)

jhiggins7 Sat 20 January 2018 05:05

Well good. That's a tough job COMPLETE! I hope you're happy with the results.

Thanks for sharing more progress photos.

YANLM Mon 22 January 2018 08:00

10.40.364 steel tubing replacement
hello. can i replace this part 10.40.364 (50x25x3 steel tubing) by this 60x30x3 without problems. when i look the plan it seem possible. but i'm not sure about the screws or something else.

YANLM Mon 22 January 2018 08:09

Sous le soleil de l'île de la Réunion / Under the sun of the Reunion Island
a link to discover "the ultimate island" :)
(It is not from me it is the tourist office)

YANLM Mon 22 January 2018 08:20

5 Attachment(s)

Borko Mon 22 January 2018 12:37

What a exotic place. I discovered it through our forum.
Yannick, you are doing good progress.

MetalHead Wed 24 January 2018 06:05

Progress looking great. Glad to see build posts!!

Robert M Sat 27 January 2018 09:25

..."Glad to see build posts"...ici aussi ;)

YANLM Sun 04 February 2018 07:30

1 Attachment(s)
Hello, photo of the construction. I am going to begin the electric part soon

YANLM Mon 05 February 2018 10:40

3 Attachment(s)
it's not easy but with a bit of patience.

MetalHead Tue 06 February 2018 04:31

Looking great! Like the progress.

YANLM Mon 12 February 2018 11:08

4 Attachment(s)
some progress

MetalHead Tue 13 February 2018 04:30

Looking good!

YANLM Tue 13 February 2018 09:38

3 Attachment(s)
Soon the cabling

IamDave Sat 03 March 2018 06:09

I just stopped by to check on you, Yannick. I am hoping good progress for you.

YANLM Sat 03 March 2018 09:10

I moved forward on the construction. All the axes work. But at the moment I have difficulty with mach3.

IamDave Sat 03 March 2018 12:12

If you post a little bit of problem, I help search on here for a solution. "Lots of really talented people, have posted good information. It is just hard to find."

YANLM Tue 06 March 2018 18:59

3 Attachment(s)
the wiring is almost complete.

YANLM Wed 07 March 2018 10:45

wiring complete
estop and push button too
but I am completely blocked by the spindle which does not start with mach3. Anybody would have a vfd Fuling ?

YANLM Wed 07 March 2018 10:51

6 Attachment(s)
The construction in image

IamDave Thu 08 March 2018 07:19

Is this the one you have, Yannick?

YANLM Thu 08 March 2018 08:11

1 Attachment(s)
hello Davey, i have seen this video before. It's not the same model but the parameters seems to be the same when i compare with the user manual of my model (downloaded because the user manual delivered with the vfd is in chinese).

In manual mode it work very well.

ifffff Fri 09 March 2018 07:22

Did you switched parameters from inverter menu to change command source?
P0.01 from 0 to 1 keyboard to terminal control
P 0.03 from 0 to 1 to control ferquency instead keyboard 0-10v source pages 20-21

YANLM Fri 09 March 2018 08:14

hello Ivo
Yes i have changed the command source.
i see variation on the vfd screen, when i jog 0-10v with the breakout board software. i found 24v between S1 and DCM and variation when i measure between VI and ACM .
I found 24 V between S1 and DCM when i activate the relay but i also found 24v when the relay is not select !!
and ACM and DCM are connected to 0V on my bob (all 0V on Bob are connected).

All times are GMT -6. The time now is 15:01.

Powered by vBulletin® Version 3.8.3
Copyright ©2000 - 2019, Jelsoft Enterprises Ltd.