70. Control Systems - Page 3 - MechMate CNC Router Forum

		MechMate CNC Router Forum > Electrical & Electronic
70. Control Systems

Options

Profile

Last 1 | 3 | 7 Days

Today's Posts

Mark Forums Read

Page 3 of 4

Threads in Forum : 70. Control Systems

Forum Tools

Search this Forum

Thread / Thread Starter	Last Post	Replies	Views
FIXED !! - Help.. uneven power out of the contactor. Now the z drive isn't working Kornerking	Sun 24 December 2017 09:07 by Kornerking	14	19,046
Limit Switches - optical / mechanical / proximity ( 1 2 3 ... Last Page) Gerald_D	Sun 24 January 2016 15:32 by darren salyer	333	340,246
Setting up a remote pushbutton as an input to Mach3 Gerald_D	Sat 22 March 2014 11:37 by Tom Ayres	27	51,093
PMDX parallel port break out card for the MechMate ( 1 2 3 ... Last Page) Gerald_D	Fri 13 December 2013 05:05 by KenC	116	141,161
Basic schematic of a typical CNC control box Gerald_D	Sat 06 July 2013 14:10 by IPenev	14	36,417
MechMate DIY Control box full spec screened spindle 3phase ( 1 2 3) Gerald_D	Sun 07 April 2013 17:50 by smreish	79	105,742
The Simulator - an essential "kitchen table" project Gerald_D	Thu 27 September 2012 19:26 by jask	22	41,654

Going from 30amps to 15amps Regnar	Thu 25 February 2010 14:15 by Regnar	2	4,828
My PC does not have a parallel port - how can I drive the PMDX-122? mrloeng	Fri 12 February 2010 04:00 by Surfcnc	25	20,845
Relay info m_leblanc	Sat 23 January 2010 20:44 by Gerald D	8	10,293
Vibration and Feedback Problems - C10 BOB with KL4030 Drivers and KL23H286208B Motors evancnc627	Fri 08 January 2010 11:37 by Gerald D	2	6,137
Making full use of the PMDX-122 ( 1 2) KenC	Thu 24 December 2009 16:47 by lumberjack_jeff	35	29,395
Advice on Proximity Sensors jehayes	Sat 12 December 2009 17:11 by jehayes	2	6,306
What is a "charge" pump? alan254	Tue 24 November 2009 08:31 by riesvantwisk	10	12,262
c11 board video input mach3 Scotty	Mon 23 November 2009 15:28 by jeffa	2	6,586
limit-settings/pin's and port's kongblom	Fri 20 November 2009 09:39 by sailfl	6	8,646
Cheap Control Box Radishworks	Fri 20 November 2009 02:20 by KenC	3	8,732
Slaving a motor - put its drive in parallel to another drive on the same BOB output ( 1 2) J.R. Hatcher	Mon 16 November 2009 09:13 by m_leblanc	34	32,653
Contactor for 115V... salewis	Tue 10 November 2009 06:33 by jhiggins7	3	7,347
PMDX-122 vs PMDX-125? salewis	Fri 06 November 2009 05:16 by salewis	6	8,927
PMDX-132 instead of the PMDX-122 SteveWellman999	Mon 02 November 2009 11:47 by jehayes	23	24,085
Router Speed/RPM Control Travish	Sun 18 October 2009 08:49 by javeria	5	8,428
i need of help renraku	Fri 16 October 2009 16:07 by renraku	2	4,936
How many CAR STOPPER BLOCKS do I need? kanankeban	Thu 15 October 2009 10:41 by jehayes	4	7,357
Help choosing a controller for a Pilot Pro router space cadet	Sun 11 October 2009 11:35 by chopper	2	6,541
Control Board Help Please paul60	Wed 07 October 2009 22:52 by Gerald D	8	11,411
Driving a relay using 2n3904 javeria	Tue 29 September 2009 21:18 by Richards	8	10,299
Version 201 Controller Board from ShopBot Gerald D	Wed 09 September 2009 20:56 by Richards	14	17,433
Control box location ! - Wall vs Table base Robert M	Mon 07 September 2009 13:03 by Alan_c	13	14,689
Router on and off - mach3 Retief	Fri 03 July 2009 01:42 by Gerald D	9	11,188
Isolator switch ? andyclarkecncuk	Wed 24 June 2009 11:46 by andyclarkecncuk	12	13,514
Can I run geckos from the output of the SB board? Kenrbass	Mon 22 June 2009 12:31 by Kenrbass	4	6,567
Smoothstepper USB to parallel converter Gerald D	Tue 19 May 2009 03:28 by sailfl	25	32,671
AC motor & VFD used with Mach3 in large CNC stone cutting system ( 1 2) osman100	Sun 17 May 2009 09:16 by Gerald D	39	45,528
Electronics Order Spreadsheet jhiggins7	Wed 08 April 2009 07:44 by jhiggins7	0	6,250
Setting up E-Stop and Limit Switches in Mach3 rocky2889	Fri 03 April 2009 10:27 by rocky2889	3	7,780
Making a wish list Medemt	Wed 25 March 2009 18:22 by domino11	1	7,034
Way over my head... SteveE	Wed 04 March 2009 10:24 by travisc	9	11,244
Servo motor encoder wiring - is my diagram correct? rocky2889	Sun 01 March 2009 20:49 by rocky2889	10	11,297
Gantry & Car Control Boxes, switch info ? kanankeban	Sat 21 February 2009 11:01 by kanankeban	0	6,210
PMDX-122 relay output voltage? chopper	Thu 04 December 2008 07:00 by Gerald D	10	12,296
why two proxies on gantry? chopper	Sun 30 November 2008 11:23 by Gerald D	11	10,410
PMDX and Gecko 203 gixi	Thu 27 November 2008 19:38 by BHawthorne	6	8,912
Home Supply Requirements jbmclain	Thu 23 October 2008 07:30 by domino11	3	6,550
Printer Cable Box - Connector sailfl	Sun 21 September 2008 21:19 by domino11	2	6,408
Would Parker Compumotor OEM650 drives work with the Oriental Motors? gmcray	Wed 27 August 2008 13:23 by Richards	1	5,731
Ladder Logic Richards	Thu 07 August 2008 09:32 by Richards	0	4,684

Page 3 of 4

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

Forum Jump

All times are GMT -6. The time now is 15:35.