701. Motor Drives - MechMate CNC Router Forum

		MechMate CNC Router Forum > Electrical & Electronic
701. Motor Drives

Options

Profile

Last 1 | 3 | 7 Days

Today's Posts

Mark Forums Read

Page 1 of 2

Threads in Forum : 701. Motor Drives

Forum Tools

Search this Forum

Thread / Thread Starter	Last Post	Replies	Views
Differences between G201, G202 and G203 stepper drives from Geckodrive ( 1 2) Gerald_D	Tue 03 April 2012 12:06 by darren salyer	59	47,442
Using the Gecko G540 drive a MechMate ( 1 2) stefanv	Sat 07 May 2011 04:45 by MAC2009	42	39,785
Geckodrives (California USA) ( 1 2 3 ... Last Page) Gerald_D	Fri 09 July 2010 13:20 by renraku	148	92,177

Spindle Frequency? lukebarber	Sat 23 March 2019 19:36 by lonestaral	2	7,988
Huanyang bit the dust, replaced with Lenze, question about parameters... Diplocaulus	Mon 28 January 2019 15:18 by danilom	1	2,182
Spindle won't stop spinning at program end or "Stop" engaged. Diplocaulus	Wed 26 December 2018 20:56 by ger21	5	3,338
Setting up a Huanyang HY02D223B VFD Jayson	Fri 02 November 2018 08:25 by ifffff	20	25,279
Buck Boost Transformer 380V 240V 3phase lukebarber	Fri 24 August 2018 20:15 by MetalHead	1	2,646
Gecko 203v - Blown fuse beckj	Sun 24 December 2017 10:05 by Kornerking	5	8,282
Read from Multiple Coils lukebarber	Thu 02 March 2017 13:04 by danilom	1	4,901
half-coil wiring of KL34H280-45-8A buddyLumen	Wed 01 June 2016 20:19 by buddyLumen	2	5,566
Stepper motor & Driver from Oriental motor steven29	Sun 17 May 2015 12:20 by Richards	17	13,254
massmind diy stepper drivers userandrew	Fri 27 February 2015 18:52 by userandrew	6	5,509
Geckodrive announced the GM215 stepper motor drive Richards	Sun 18 January 2015 11:21 by Robert M	1	3,598
Use Arduino Uno to test stepper drivers and stepper motors Richards	Sat 13 December 2014 12:12 by Richards	0	3,430
Gecko 203v intermittent fault paul60	Fri 12 September 2014 17:54 by smreish	17	13,757
Suspect gecko G 203V problem paul60	Thu 03 October 2013 10:19 by Richards	5	5,766
How much voltage do I really need? Richards	Thu 18 July 2013 18:54 by Richards	29	16,758
How to calculate resistor needed for gecko drives Richards	Wed 15 May 2013 09:52 by smreish	8	7,628
110 volt stepper driver...no need for PS? IMMark	Wed 20 February 2013 00:39 by Surfcnc	4	5,061
dual motor on Y axis wiring ? shikha829	Mon 28 January 2013 21:07 by javeria	8	8,790
open source drives g540 equivalent lolailando	Thu 10 January 2013 07:02 by darren salyer	4	4,792
Motor Not Locking Up on Power Up Surfcnc	Wed 14 November 2012 04:30 by Surfcnc	7	5,990
Would a size 23 motor work? Richards	Thu 08 November 2012 10:12 by Richards	3	4,784
Ruminations on production and stepper motors Richards	Tue 23 October 2012 07:31 by bradm	8	5,841
Nema 34 set at 6000 velocity stops rotating viz	Sun 21 October 2012 03:49 by viz	20	11,888
New Gecko Faulting - RED LED tnarch	Fri 19 October 2012 00:56 by KenC	7	5,915
Yasakawa V100 VFD Kobus_Joubert	Mon 16 January 2012 09:34 by Kobus_Joubert	12	7,217
Cheaper drives SLINK	Wed 30 November 2011 03:33 by aniljangra	13	9,567
5 phase stepper motor. unns_boy	Mon 12 September 2011 17:58 by PEU	3	4,681
Selecting resistors for Gecko drive Rusty Nuts	Mon 29 August 2011 20:49 by smreish	9	5,728
Servos for gecko drives. agfmaquinas	Thu 24 March 2011 16:45 by Jason Marsha	5	6,118
Gecko 201X Adjust Screw tnarch	Wed 23 March 2011 10:11 by MetalHead	2	4,477
Complete manual for Chinese VFD chrisd7306	Sat 20 November 2010 13:11 by Drad98_98	6	6,053
parallel port with mach3, or USB with usbcnc? cnc'tje	Fri 22 October 2010 10:56 by cnc'tje	12	12,157
Question about stepper drives and motor direction DTGuitars	Mon 18 October 2010 10:38 by bradm	13	9,867
Using steel control box as the heat sink G540 jwt	Mon 11 October 2010 10:22 by bradm	3	4,155
Andeli inverter english translation manual DenisCasserly	Fri 24 September 2010 18:35 by DenisCasserly	0	3,335
QJ8060 Drive from CW-Motors Francois	Tue 14 September 2010 13:31 by Francois	13	10,774
how to assign gecko driver to motors? renraku	Sun 12 September 2010 16:48 by Red_boards	3	4,677
One system controlling two tables? Mountaincraft	Fri 10 September 2010 19:27 by smreish	4	6,828
Dead Gecko's in S.Africa - a collection point for bulk return for repair Gerald D	Fri 09 July 2010 13:21 by Kobus_Joubert	8	6,500
digital stepping driver KenC	Sun 20 June 2010 11:20 by fanefane	7	8,040

Page 1 of 2

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

Forum Jump

All times are GMT -6. The time now is 21:46.