Motors & their mountings - Page 2 - MechMate CNC Router Forum

		MechMate CNC Router Forum > Common Assemblies & Parts
Motors & their mountings

Options

Profile

Last 1 | 3 | 7 Days

Today's Posts

Mark Forums Read

Page 2 of 3

Threads in Forum : Motors & their mountings

Forum Tools

Search this Forum

Thread / Thread Starter	Last Post	Replies	Views
Why a stepper motor should not be too big . . . . Gerald_D	Wed 11 March 2020 01:20 by maoxinai4	6	42,356
M310100K Springs for loading motors against the racks Gerald_D	Tue 10 June 2014 04:08 by Fox	11	28,976
Selecting motors for the MechMate ( 1 2 3 ... Last Page) Gerald_D	Tue 26 February 2013 07:27 by Gerald D	278	280,158
MetalHead Metal Motor Plate Setup MetalHead	Wed 09 November 2011 06:23 by MetalHead	20	37,077
Wiring the PK296A2A-SG7.2 motors & power supply voltage selection ( 1 2 3 ... Last Page) Richards	Fri 29 July 2011 10:46 by bradm	97	140,042
Unipolar, Bipolar series, Bipolar parallel, choices for 2phase steppers ( 1 2) Gerald_D	Fri 26 February 2010 20:16 by sprayhead	47	75,145

ebay shop "easy cnc" mrghm	Tue 19 October 2010 04:28 by danilom	1	7,848
Motion King 34HS6803-G5 and G10 cheap gearboxed steppers hutchcj	Mon 11 October 2010 23:07 by Gerald D	6	10,725
How to guarantee zero backlash when mounting the motor mounts... sprayhead	Sat 28 August 2010 08:19 by sprayhead	4	7,360
Starting point for motors. tangocharlie123	Mon 19 July 2010 22:53 by Kobus_Joubert	5	8,490
How much Torque is required when cutting? Regnar	Wed 23 June 2010 23:10 by eesanopi	9	14,209
Direct motors 4Nm and 6,8Nm tomasptacek	Wed 26 May 2010 02:25 by tomasptacek	0	4,728
what brake to use Darkseid	Fri 07 May 2010 19:37 by Gerald D	2	5,253
How many motors use mechmate in the long axis albertoslayer	Tue 09 March 2010 10:44 by rick748	11	15,835
A show of hands - MM builders who have found their motors running hot? Gerald D	Sun 28 February 2010 11:35 by Richards	20	18,368
does anyone offer a kit with 7:1 reduction with nema 34 motors . . . . . toad	Thu 28 January 2010 00:08 by peter__jackson	25	24,738
Makita Router Bracket hennie	Wed 20 January 2010 04:43 by KenC	9	9,577
Advice on Wantai Motors jehayes	Wed 20 January 2010 04:41 by KenC	6	9,034
Parts recycling Claudiu	Sat 12 December 2009 22:24 by Gerald D	2	5,202
Coil Inductance measurement, is this normal? KenC	Thu 19 November 2009 01:36 by KenC	8	10,290
Understanding OM's taper-hobbed (TH) gearbox Gerald_D	Tue 20 October 2009 10:45 by Gerald D	3	5,675
Keling KL34H280 Power Supply Help Wanted Castone	Tue 01 September 2009 22:39 by Richards	4	7,576
In need of a little advise from the experts...series or half-coil wiring? jeffa	Mon 17 August 2009 11:57 by Gerald D	7	10,304
Would you mind to help me to solve the problem for Keling stepper Motor Driver? qangel1000	Fri 07 August 2009 23:42 by qangel1000	6	9,271
Noise from stepper motors when standing still? lunaj76	Mon 27 July 2009 22:50 by Kobus_Joubert	8	8,047
Z-axis stepper motor is too hot gixi	Sun 26 July 2009 11:11 by gixi	19	19,566
Position accuracy & torque of stepper before slip & slip amount Gerald D	Wed 15 July 2009 02:05 by Gerald D	0	5,139
Duty Rating stepper motors - setting the drive current Gerald D	Tue 23 June 2009 05:07 by javeria	26	25,973
Off the shelf belt drive? myozman	Mon 22 June 2009 19:41 by myozman	2	8,648
Gearbox Backlash Is this to be expected? Cutter99	Mon 15 June 2009 11:07 by Gerald D	4	9,332
What do you think about these motors? shelbygt500buddy	Sun 14 June 2009 18:11 by J.R. Hatcher	8	9,927
Where can I find a Motor Shaft Coupler for planetary gearbox? rocky2889	Tue 03 March 2009 20:11 by rocky2889	2	6,039
Initial opinions with this geared motor: sprayhead	Fri 30 January 2009 07:05 by Gerald D	1	5,548
My PK296-02AA motors are too low on power output, what can I do? knownuttn	Fri 16 January 2009 18:32 by Marc Shlaes	7	10,131
NEMA23 vs NEMA34 servant74	Sun 04 January 2009 17:22 by bradm	2	6,837
Servo versus Stepper motors ( 1 2) Manjeet Singh	Fri 02 January 2009 22:43 by Richards	36	33,965
Generic Aussie (Leadshine) Stepper Motors are they OK? Jama	Tue 23 December 2008 08:05 by Gerald D	5	12,323
Anyone used Fulling motors? sprayhead	Sat 06 December 2008 16:34 by sprayhead	5	7,908
Are these the same: Pk296ae-sg7.2 (metric) = Pk296a2a-sg7.2 (inch)? gixi	Wed 26 November 2008 13:39 by jan stransky	15	16,102
Same torque, different sized frame chrisd7306	Wed 19 November 2008 02:25 by Gerald D	5	8,403
Damper for stepper motors Delamination	Mon 17 November 2008 11:34 by Delamination	0	5,562
Keling Stepper motor John	Mon 27 October 2008 10:39 by Conrado_Navarro	14	17,504
Stepper motor wire colours do not match supplier's info - how to figure them out hennie	Sun 14 September 2008 06:41 by Gerald D	19	17,325
True Torque of a Servo motor for comparison to a Stepper motor, when used in a router Mcyoda	Tue 19 August 2008 00:50 by Gerald D	3	9,763
What does a stepper motor look like inside? (geared Oriental Motor) Gerald D	Sat 16 August 2008 08:29 by Gerald D	0	8,801
stepper motors what brand to use???? chopper	Sat 19 July 2008 11:42 by Gerald D	19	19,809

Page 2 of 3

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

Forum Jump

All times are GMT -6. The time now is 11:05.