Troubleshooting - Page 2 - MechMate CNC Router Forum

		MechMate CNC Router Forum > After Building the Beast - Operating , Troubleshooting and Maintenance
Troubleshooting

Options

Profile

Last 1 | 3 | 7 Days

Today's Posts

Mark Forums Read

Page 2 of 3

Threads in Forum : Troubleshooting

Forum Tools

Search this Forum

Rating Thread / Thread Starter	Last Post	Replies	Views
Loosing steps - noise interference problems MariusL	Sun 15 March 2009 05:34 by MariusL	14	12,920
Loosing Steps - underpowered ? Claudiu	Thu 18 February 2010 13:53 by Richards	24	20,183
Lurching at Reset - interference from spindle VFD waynec	Thu 05 February 2009 17:00 by bradm	12	13,967
Mach dont open G codes Hugo Carradini	Sat 18 January 2014 11:02 by Hugo Carradini	7	14,892
Mach3 to HY series VFD on/off control AJWConstruction	Tue 19 October 2010 18:53 by Kenrbass	2	6,324
Machine cuts out after cutting for a while - Loose wire on E-stop circuit Hugo Carradini	Mon 31 March 2008 12:18 by Hugo Carradini	8	9,379
Machine is down,estop activated won't turn off, config check notes included Diplocaulus	Thu 10 January 2019 07:28 by Diplocaulus	4	8,646
Machine locks up while travelling at high speed - Tuning the motor speeds and accels Doug_Ford	Sun 03 February 2008 21:55 by Gerald D	3	6,871
Machine runs far too slow (or fast) and the wrong distances - Confusing inch/mm 's Hugo Carradini	Tue 25 September 2007 09:44 by Hugo Carradini	2	6,703
Machine stops responding intermitantly ( 1 2) Darin	Sun 28 July 2019 23:14 by Tanjaddaniel	37	43,075
Matty Zee Mach 3 Pluggin ( 1 2) AuS MaDDoG	Wed 19 January 2011 04:50 by Surfcnc	35	43,652
MechMate going crazy (picking up interference from motors, etc.) silverdog	Fri 15 June 2012 01:44 by silverdog	6	10,349
Milwaukee 5625 failure: electronic speed control? melissa	Tue 26 June 2012 07:49 by Kart	3	9,560
Milwaukee Router weirdness - SSR (solid state relay) not suitable jeffh	Thu 26 March 2009 12:03 by jeffh	26	24,698
motor tuning g-force in Mach preferred settings caddzeus	Thu 30 May 2019 07:03 by IamDave	1	7,130
Motors are weak and run cool - setting up a "Leadshine" drive lumberjack_jeff	Mon 04 January 2010 07:08 by lumberjack_jeff	7	9,442
Motors do not move after initial setting up - Mach setups fabrica	Fri 19 January 2007 01:04 by fabrica	17	10,394
Motors do not turn - Ports & Pins setting for charge pump ( 1 2) Conrado_Navarro	Fri 10 July 2009 22:08 by Gerald D	37	27,086
Motors do not turn properly - poor quality wiring used for testing martin77pl	Tue 31 March 2009 11:36 by martin77pl	8	8,403
Motors loosing steps - Breakout board not suitable mgandy02	Mon 02 November 2009 10:01 by mgandy02	17	16,682
Motors move too slowly - unresolved Gato Richy	Wed 20 May 2009 23:04 by Gerald D	10	10,077
Motors Will Not Turn - Step & Direction wires crossed by mistake toad	Sun 01 August 2010 10:49 by JamesJ	17	13,376
Motors won't turn after the setting up - PMDX-122 jumpers incorrect lunaj76	Fri 31 October 2008 04:20 by J.R. Hatcher	13	11,477
Moves at different speeds for different directions - feed rates incorrectly defined Kobus_Joubert	Sun 22 March 2009 05:16 by Gerald D	16	15,303
My Router Motor Died, Now What! mersigns	Sun 03 June 2018 10:54 by pblackburn	5	13,195
Need help with jog speed in Mach3 motor tuning !!! ( 1 2) rival	Sat 03 September 2011 05:03 by Surfcnc	45	48,272
No 5V supply out of PC - Polarity reversed J.R. Hatcher	Thu 24 January 2008 16:50 by J.R. Hatcher	1	4,316
Odd overshoot in Y axis when changing direction ( 1 2) JamesJ	Sat 10 September 2011 13:13 by Gerald D	32	33,361
One axis looses steps when going fast under load - change accel setting Greg J	Sun 07 December 2008 21:55 by Gerald D	10	11,225
One motor goes wrong way - How to reverse its direction grandpi	Sun 17 February 2008 22:03 by Gerald D	2	6,058
One of the four motors not running properly - faulty Geckodrive 203V cncb	Sat 08 November 2008 07:46 by cncb	8	12,110
One stepper motor does not change direction - drive needs reset waynec	Mon 16 February 2009 09:22 by waynec	13	15,157
Parallel cable does not work - all the cores are not present martin77pl	Thu 30 July 2009 09:14 by javeria	9	9,949
pmdx 133 fried Kart	Sun 19 August 2012 13:18 by JasonC	7	11,978
Power Contactor Not Working Regnar	Sat 10 April 2010 12:38 by bradm	28	27,654
Problem with slaved axis MK_CATANZARO	Fri 02 January 2015 10:58 by danilom	4	12,307
Problem with Tabs ... it leaves vertical signs silverdog	Tue 12 June 2012 23:27 by hennie	15	18,396
Problems with cooling fan.. - impeller touched the mounting plate cncb	Tue 04 November 2008 04:47 by cncb	17	13,113
Proper Homing javeria	Sun 24 January 2010 05:28 by sailfl	25	20,282
Pulling whatever is left of hair and no solution digger	Sun 06 November 2016 18:13 by digger	11	18,463

Page 2 of 3

Forum Tools	Search this Forum
Mark This Forum Read View Parent Forum	Search this Forum : Advanced Search

	New posts		Hot thread with new posts
	No new posts		Hot thread with no new posts
	Thread is closed

Posting Rules
You may not post new threads You may not post replies You may not post attachments You may not edit your posts BB code is On Smilies are On [IMG] code is On HTML code is Off Forum Rules

Forum Jump

All times are GMT -6. The time now is 20:35.